Exactly How to Remove and Change a Tub
Exactly How to Remove and Change a Tub
Blog Article
The article which follows relating to A Step-by-Step Guide to Installing a Bathtub is highly enjoyable. Don't miss out on it.
Installing a tub isn't specifically rocket science, yet it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately hard job. If the old bathtub is easily accessible, the task can move immediately; if you have to open up a wall to eliminate the old tub as well as place the new bath tub, the task is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the new one. Make certain you have certified yourself for the work and are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will certainly aid you set up a new tub in your bathroom if you have actually already acquired a new bathtub and do not need to change the plan of your previous water supply pipelines.
Your tools as well as material list ought to comprise the following:
Getting ready for the Installation
To start with, the sustaining frame provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also practical to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The procedure of eliminating the existing faucets can be fairly problematic because of the limited gain access to that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Tub
Making use of both wood boards under its feet, place the tub in the called for position. The wooden boards are practical in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bathtub until the spirit level reviews level.
To install taps, fit all-time low of the outermost adaptable tap connector to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water and also examine all joints and also brand-new pipework for leakages and also tighten them if essential. Fill up the tub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub should wait till the bath tub has actually been utilized at least when as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet and the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind should be linked to the tap ends first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall in between the bath and also the tiling, resulting in difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed reading our post about How to Install a Bathtub. Thank you for taking the time to browse our piece of content. Remember to take the time to promote this blog posting if you liked it. We cherish reading our article about How to Install a Bathtub.
Browse Our Site
Report this page